Repetier server init.d script install#
Repetier server init.d script drivers#
Repetier server init.d script update#
Repetier server init.d script series#
Repetier server init.d script mac#

This is the correct value for the Semitec 104GT-2 thermistor used in the popular E3D hot ends, to give accurate readings around 220C.

The hot end thermistor B value defaults to 4388 (M305 command).

If you are using the DuetWiFi to control an Ormerod printer, you will need to use T10000 in the M305 P0 command.

The bed thermistor resistance defaults to 100000 instead of 10000 (T parameter in M305 command).

Repetier server init.d script series#

The thermistor series resistance defaults to 4700 instead of 1000 (R parameter in M305 command).

Microstepping defaults to 16x with interpolation. We suggest that in your config.g file you set microstepping before you set the steps/mm. The steps/mm will be adjusted automatically when you change microstepping. For example, M350 X128 I0 will set the X drive to 128x microstepping without interpolation.

The M350 command to change microstepping is supported.

Repetier server init.d script mac#

On the Duet 2 WiFi, the M540 command (set MAC address) has no effect.

With firmware 1.19 and later you can set these parameters individually for each access point you connect to, using the M587 command. Likewise, the M553 and M554 commands to set the netmask and gateway have no effect.

The IP address will be allocated by your WiFi router using DHCP. On the Duet 2 WiFi, setting the IP address using M552 has no effect.A M552 S1 command in config.g will only take effect after the rest of config.g has been fully processed. Use M552 S1 in config.g to enable it at startup. Networking is disabled at startup by default.This is how the Duet 2 WiFi and Duet 2 Ethernet firmware differs from the Duet 0.8.5 and 0.6.

Repetier server init.d script drivers#

NOTE: the folders /firmware, /gcodes, /macros, /menu, /sys, and /More information on where to get the firmware files and Duet Web Control files is explained lower down on this in the where to get firmware, software and drivers section.Ĭhanges to config gcodes and firmware behaviour between Duet 2 and Duet 0.8.5 / 0.6 The config tool can be used to setup these files for your printer type. They are invoked automatically and by the M401 and M402 commands. If your Z probe needs to be deployed and retracted, the script files deployprobe.g and retractprobe.g are used.are optional files that can be configured to run when particular endstop pins are triggered, for example by an emergency-stop button. In RepRapFirmware 3.x, file Duet2CombinedIAP.bin or DuetMaestroIAP.bin is used instead.

Repetier server init.d script install#

iap4e.bin (Duet WiFi/Ethernet) or iap4s.bin (Duet Maestro) is a helper file used to install new main firmware.

stop.g is optional, but if present is run when a SD card print finishes normally with a M0 command at the end of the print job.

start.g is optional, but if present is run whenever you start a job from the SD card.

cancel.g is optional, but if present is run when you cancel a paused print.

resume.g is run when you resume a print.

bed.g holds the script for probing the bed and calculating bed compensation on a Cartesian or CoreXY printer, or doing delta calibration on a delta printer.

For a delta printer there is homedelta.g instead.

homex.g, homey.g, homez.g and homeall.g are the homing scripts for a Cartesian or CoreXY printer.

Your config.g file should normally include command M501 near the end, to load these saved values at startup and override any similar commands earlier in config.g.

config-override.g holds the configuration parameters that were saved when you last ran M500.

config.g holds the firmware configuration script, which is executed at startup.

It should contain at least the following files:

Repetier server init.d script update#

Compatible with Duet 3 mini 5+ and Duet 2 Maestroįolder /sys is used to hold system configuration files and, in all firmware versions before RRF 3.3, firmware update files ready for installation. This holds the files that define the menu layouts for 128圆4 pixel monochrome displays. See Macros for examples of useful user macros.įolder /menu. You can use subfolders of /macros to organize these files. The names of these files appear as menu entries in DuetWebControl and on PanelDue. G-code files can also be located on an external SD card if one is connected.įolder /macros is used to hold used-defined macro files. You can use subfolders of /gcodes to organize these files. This holds firmware update files ready for installation.įolder /gcodes is used to hold g-code files for printing.

These Duets use the following folder structure:įolder /firmware.